from the device, ensure that all power cords are disconnected from the power source. 1. 2 x System x Types , , , and User’s Guide. This Installation and User’s Guide contains information and instructions for setting up your IBM System x M2 Types and server, instructions for. This Problem Determination and Service Guide contains information This document is in PDF on the IBM System x Documentation CD.
|Published (Last):||3 November 2017|
|PDF File Size:||20.38 Mb|
|ePub File Size:||15.17 Mb|
|Price:||Free* [*Free Regsitration Required]|
Removing And Replacing Tier 2 Crus Updating The Server Configuration Removing The Front Fan Cage Assembly Removing the front fan cage assembly To remove the front fan cage assembly, complete the following steps: Server Controls, Leds, And Connectors Page 44 1, DIMM connector 7 channel 2 and connector 10 channel 3 rather than branch 0, then branch 1 will support online-sparing and branch 0 will not.
If your system has a module containing a lithium battery, replace it only with the same module type made by the same manufacturer.
The IBM ServicePac is a series of prepackaged warranty maintenance upgrades and post-warranty maintenance agreements with a well-defined scope of services, including service hours, response time, term of service, and service agreement terms and conditions. Page 19 Table 2. System-board External Connectors Don’t show me this message again.
IBM System x3400 Type 7976 Manuals
The System X Server Follow these guidelines when you work inside a server that is turned on. Set any jumpers or switches on the drive according to the documentation that comes with the drive. Page Page – Appendix. Removing The Simple-swap Backplate Setup And Configuration Overview Removing And Replacing Server Components Press down firmly on the heat sink until it is seated securely.
Configuring The Server Front view The following illustration shows the controls, LEDs, and connectors on the front of the hot-swap server models.
Changes are made periodically to the IBM Web site.
Removing The Serveraid 8k-l Adapter Before you install optional hardware, make sure that the server is working correctly. Table Of Contents Reliability, availability, and serviceability Open the retaining clips and, if necessary, remove any existing DIMM. Static electricity that is released to internal server components when the server is powered-on might cause the server to stop, which could result in the loss of data.
System-board option connectors S3400 following illustration shows the system-board connectors for user-installable options. Removing the front fan cage assembly To remove the front fan cage assembly, complete the following steps: Three speed-controlled hot-swap Diagnostic LEDs: If you are instructed to return the hot-swap power supply, follow mznual packaging instructions, and use manjal packaging materials for shipping that are supplied to you.
To find updated information about configuring the controller, complete the following steps. Page 8 Minimum configuration: Removing And Replacing Frus Server Controls, Leds, And Power In your file, the entire entry must all be on one line. For proper collection and treatment, contact your local IBM representative. EMC shields Tape drive 7. Hazardous voltage, current, and energy levels are present inside any component that has this label attached.
Ibm System x Type Manuals
When replacing the lithium battery, use only IBM Part Number 33F or an equivalent type battery recommended by the manufacturer. Page 14 Statement IBM may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you.
Do not make changes in the Advanced Chipset Control option unless you are directed to do so by an IBM authorized service representative. Touch the static-protective package that contains the drive to any unpainted metal surface on the server; then, remove the drive from the package and place it on a static-protective surface.
IBM is not responsible for any radio or television manuao caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment.
For more information about the requirements for SAS cables and connecting SAS devices, see the documentation that comes with these devices.
Using the baseboard management controller configuration utility program Use the baseboard management controller configuration utility program to view or change the baseboard management controller configuration settings. Lower the fan cage assembly into the chassis and press down firmly until the fan cage assembly is seated firmly in place. Turning Off The Server The System x server Page 16 – Notices and statements in this document Page 17 – Machine Types and features and Installing An Optional Tape Drive Installing The Front Adapter-retention Bracket Page Part Number: Removing The Serveraid-8k Adapter Table Of Contents Performing The Checkout Procedure Solving Power Problems Turn off the server and peripheral devices, and disconnect the power cords and all external cables.