iso – Download as PDF File .pdf), Text File .txt) or read online. Safety of Machinery Documents Similar To iso Bs en Iso – Part 2. EN ISO and EN ISO are Type A standards (basic safety standards) and therefore have a dual purpose: they are. BRITISH STANDARD BS EN ISO Incorporating Corrigendum No. 1 Safety of machinery — Basic concepts, general principles for.
|Published (Last):||13 November 2004|
|PDF File Size:||11.50 Mb|
|ePub File Size:||17.96 Mb|
|Price:||Free* [*Free Regsitration Required]|
For measures for vibration isolation of stationary industrial machinery see EN Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Factors to be taken into account when estimating the possibility of avoiding or limiting harm 121000-2, among others, the following: It supersedes BS EN At least the following requirements shall be met: Potential consequencesb discomfort; loss of awareness; loss of balance; permanent hearing loss; stress; tinnitus; tiredness; any other for example, mechanical, electrical as a consequence of an interference with speech communication or with acoustic signals.
Taking into account general technical knowledge of machine design 3 4 6. In large automated installations, particular attention shall be given to safe means of access, such as walkways, conveyor bridges or crossover points.
Safety of machinery: EN ISO 12100-1 and EN ISO 12100-2
In some cases, it is enough to use only one of the columns, particularly when hazards are in the same hazard zone and can be grouped together in terms of protective measures. As shown in Figure 1, the adequacy of the risk reduction shall be determined after applying each of the three steps of risk reduction described in Clause 6.
When determining these elements, it is necessary to take into account the aspects given in 5. Inherently safe design measures Step 2: NOTE 2 Machine start-up during normal sequence of an automatic cycle is not unintended, but can be considered as being unexpected from the point of view of the operator.
With this in isl, it shall inform and warn the user about residual risk. This means that the characteristics and performances of the machine or a 12100-2 of machines wn an integrated process, and the related people, environment and products, should be identified in terms of the limits of machinery as given in 5. On machinery intended for lifting persons, controls for lifting and lowering and, if appropriate, for moving the carrier, shall generally be located in the carrier.
Means of access to parts of machinery located at a height shall be provided with collective means of protection against falls e. Durability and availability of the documents: Several methods are available for the systematic identification of hazards. While automatic feeding and removal devices have much to offer in preventing accidents to machine operators, they can create danger when any faults are being corrected.
Worldwide Standards We can source any standard from anywhere in the world. Certain safeguards may be used to avoid exposure to more than one hazard e. General principles for design or a Type C standard eg BS Control actuators shall be designed or guarded so that their effect, where a risk is involved, cannot occur without intentional operation see ISOISO and ISO NOTE 2 Depending on its construction, a guard may be described as, for example, casing, shield, cover, screen, door, enclosing guard.
In order to offer more detailed information on the type of hazards, there are two additional columns that correspond to the origin of the hazard and its potential consequences. Appropriate words should be selected and combined to describe the hazard in the most convenient way.
Where, for describing a hazard, more than one of the columns presented in Table B. Where fixed guards are held in place by fasteners, Sub-clause 5. The use of one or more of the columns presented in Table B. The walking areas shall be made from materials which remain as slip resistant as practicable under working conditions and, depending on the height from the ground, shall be provided with suitable guard-rails see ISO See Figure 4 and ISO They shall provide the minimum possible interference with activities during operation and other phases of machine life, in order to reduce any incentive to defeat them.
Openings shall whenever possible open towards a safe position. Clause 4, ‘Inherently safe design measures,’ gives examples of geometrical factors that should be considered.
For cycle initiation by a sensitive protective equipment, only active opto-electronic protective devices AOPDs complying with IEC series shall be used, provided that: Standards are also available from the BSI website at http: Principes techniques ISO The concept of safety of machinery considers the ability of a machine to perform its intended function s during its lifecycle where risk has been adequately reduced.
While the foregoing discusses the body of Part 1 of the standard, there are also some additional information included.
Safety of Machinery: EN ISO and EN ISO
Information for use consists of communication links, such as texts, words, signs, signals, symbols or diagrams, used separately or in combination to convey information to the user. NOTE This control mode shall be associated with one or more of the following measures: Basic concepts, general principles for design. The interfaces between zones shall be designed such that no function in vs zone creates hazards in another zone which has been stopped for an intervention.
General requirements for the design and construction of fixed and movable guards deals specifically with the guarding design, but the subject is also covered to a lesser extent in EN ISO Clause 5.
Standardized phrases shall be considered be important messages such as warnings need to be given see also IEC b Consideration shall be given to the enclosure of control positions or intervention zones to provide combined protection against several hazards including a b c d hazards from falling or ejected objects, using, for example, protection in the form of a falling object protection structure FOPSemission hazards protection against noise, vibration, radiation, substances hazardous to health, etc.
The different kinds of guards and protective devices are defined in ISO This covers everything from ‘machinery’, ‘hazard’ and ‘risk’ to ‘adequate risk reduction’, ‘common cause failures’ and ‘common mode failures.